Weekend Project: DIY Personalized Dog Tags How-To/Tutorial

Weekend Project: DIY Personalized Dog Tags How-To/Tutorial

May 1, 2012

Share the Rowe:
Pinterest Facebook Twitter Email

DIY Personalized Dog Tag How ToDIY Personalized Dog Tag How To

**Due to popular demand, I now sell these in my Etsy shop, for those that are more “do it for me.” :)   ***

Oh, don’t be fooled. By “dog tags,” I mean REAL dog tags… that my doggies are now wearing. One of the perks of running my own Etsy shop is having the tools on-hand to do projects like this. BUT, if you’re a crafty person, the tools required to stamp something are pretty handy (and fun!) to have. Plus, personalized dog tags like this can cost more than just buying the tools and doing it yourself. So, I say just do it yourself and then you have the tools AND the tags for the same price. Just sayin…

{Tools Used}

  • Metal stamping block (Michael’s)
  • Rubber stamping block (Michael’s)
  • 3mm letter stamps, or whatever size you’d like (Michael’s/Etsy/Ebay)
  • Doming block, if you’d like to dome your discs (Michael’s)
  • Design stamps (Michael’s/Ebay)
  • 1″ & 3/4″ Raw brass discs (Monster’s Layer or Ebay)
  • Disc hole punch (Michael’s)
  • Ball pein hammer, if you want a hammered texture . If not, a regular hammer is fine. (Harbor Freight or any hardware store)
  • Sharpie
  • Fine steel wool (Harbor Freight or any hardware store)

1. Use the sharpie to map out your letters. Since I went along the curve of the disc, centering really wasn’t a concern of mine since I could just punch the final hole over whatever wound up being the center. But if you want to stamp in a line, use a Sharpie to mark your dots.

2. Place the steel block on top of the rubber block. The steel block will ensure that the full force of the hammer transfers to the disc. The rubber block absorbs force so that your table or bench doesn’t knock around.

3. Take note of the orientation of your letter, place is down on the stamp, and give it a whack with your hammer. Use the flat side of your ball pein hammer for this.

3. After all letters a stamped, rub sharpie across the letters and then remove excess with the steel wool. This is to check the impression. If you need to make another pass, carefully place the stamp in the already created grooves and give the disc another whack.

4. If you want to give your discs some hammered texture, do so now with the rounded end of your ball pein hammer. Use the steel and rubber block again.

5. At this point, you will want to punch your holes. Mark the hole with a Sharpie and punch. If you find the disc hole puncher is leaving a ring behind, place a rag between the disc and the tool only at this point to prevent this. However, don’t put anything between the actual pin that pierces the disc and the disc itself.

6. Once holes are punched, use the doming tool to lightly dome your discs, if so desired. Start with the biggest dome first and work your way to the desired angle. Be gentle, working around the outside of the disc to the center. Don’t start at the center as this will cause buckling.

7. Do a final pass with the steel wool to clean any remaining Sharpie and you’re good to go! Depending on the metal you chose, these may need to be lightly buffed and the details may need to be re-filled with Sharpie every so often. We do this at bath time since the collars are already off.

8. Fin!

<3
Andrea

P.S I wanted to show you my sexy little ladies with their new bling, but they would not sit still! Such energetic dogs…

Related Posts Plugin for WordPress, Blogger...

{ 4 comments… read them below or add one }

Terri April 26, 2013 at 1:38 am

What fun. Thanks for sharing such a great idea.

Reply

Karen September 4, 2013 at 2:22 pm

Could not locate Monster’s Layer on eBay is there another shop that sells the blanks you could recommend.

Thanks so much!

Reply

Andrea September 5, 2013 at 7:27 pm

Hi Karen! I recommend buying the blanks from Monster’s Layer OR ebay. I included a link to the Monster’s Layer site, as they are not on eBay.

Happy Crafting!
Andrea

Reply

pet id tags December 6, 2014 at 5:50 am

Nice and very creative Pet ID tags gonna try this one for my pets. Thank you for this great and informative blog.

Reply

Leave a Comment

{ 10 trackbacks }

Previous post:

Next post: